Can You Wire A Peak Back-up Camera Write To Your Plug In For Reverse

Download Article

A rear-view camera, likewise known every bit a backup camera, lets yous come across what's backside your vehicle without having to look backwards. Though the device comes standard with many new auto models, you can add a rear-view camera to your vehicle if it didn't come up with i.

1
Buy a mountable backup camera for your specific vehicle. For safety, make sure you purchase a device specifically designed to be a rear-view camera. Purchasing one made for your specific vehicle volition make it easier to install than a standard aftermarket camera. So you lot can install it easily, look for a camera that mounts onto or directly behind your license plate.^[1]
- Look for backup cameras at consumer electronics stores.
2
Go an external monitor if you want to keep your existing rear-view mirror. An external backup monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they take up more space than internal monitors, external monitors are far easier to come across and can be hands replaced if necessary.
- If yous'd like, you tin can use a standard video monitor instead. However, keep in mind that it may non have however features every bit devices designed for use with fill-in cameras.
Advertisement
3
Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully functioning rear-view mirror that houses a small screen inside the glass. Some internal monitors prune on top of your current rear-view mirror, but others replace your original mirror entirely.^[2]
- Most internal monitors shut off and disappear when not in use, making them a perfect pick if you desire to preserve your motorcar's looks.
4
Buy power and video cords if your camera and monitor didn't include them. For nearly rear-view photographic camera installations, you'll need camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cable.^[3]
- About installation kits include these cables, but some may require you lot to buy them separately.
- Some photographic camera models use wireless transmitters instead of standard video cables.
Advertisement

ane
Have off your rear license plate. Using a Phillips head screwdriver, remove each of the screws belongings your rear license plate in place. Then, pull the plate off and set it aside.^[iv]
- Make sure y'all place the screws in a safe place and so y'all don't lose them.
ii
Remove your body's interior panel. Pop open your body and look for a solid interior console covering the opposite side of your license plate mounting expanse. And then, insert a trim removal tool or other thin device behind the panel and pry it off.^[5]
- Removing this panel will expose the car's rear wiring chambers.
3
Drill a small hole in the license plate mounting area. Make sure there are no obstructions betwixt the license plate mount and the rear wiring chamber. Then, create a modest hole in the car using a power drill equipped with a high-speed twist drill chip. Line upwardly your hole and so it is directly behind where your camera's power and video cable volition go.^[6]
- To figure out where to make the pigsty, concord your camera up to the area y'all intend to mount it. Then, note the spot where its splitting cord sits.
- Create a pigsty that's big plenty to fit your photographic camera'south power and video cable.
- If you come across any obstructions, endeavour to remove them. If you lot tin can't, run into if you can make a pigsty nearby.
- For most jobs, you'll need a drill fleck that has a bore between ¹⁄_eight and ¹⁄_four in (0.32 and 0.64 cm).
iv
Place a rubber grommet around your camera cable. Earlier running your camera cable into the car, sideslip a safety grommet onto it near the non-splitting cease. These small-scale prophylactic washers, available at about home improvement stores, will keep the wire in place and preclude leaks.^[7]
- Choose a grommet that's just big enough to fit within the drilled hole.
v
Run the camera cable into your trunk. Pull the splitting end of your camera's video and power cablevision through the drilled pigsty into the trunk of your car. Brand sure y'all pull it tight so the condom grommet lodges into the drilled hole.
- Your photographic camera cable should run from the outside of the machine to the inside of the automobile.
half dozen
Locate your machine's two contrary light wires. Reverse light wires are the cords that connect your machine's tail lights to the dashboard. They hook directly into your vehicle'southward tail lights and are normally located in the hatch or trunk of your car.
- These cords look dissimilar for every vehicle so, if you tin can't discover them, consult your owner's transmission for model specific information.
seven
Strip and split up your car's opposite light wires. Using a wire stripper or pliers, skin back the rubber roofing the wires. Then, use a screwdriver or other thin tool to poke a hole through the middle of each exposed wire, separating the private wire strands.^[viii]
- For safety, make sure y'all practise this while the car is turned off.
viii
Fuse your photographic camera wires with the reverse light wires. Adhere ane of your bare wire cables to the photographic camera cord'southward power connector. Then, poke your bare wires through the center of the exposed reverse light wires and twist them together. For prophylactic, make certain you wrap the combined wires in electrical tape.^[ix]
- Make sure yous poke your positive (usually reddish) blank wire through the positive reverse lite wire and the negative (usually black) blank wire through the negative reverse light wire.
Advertisement

1
Road your camera'southward video cable to the front end of the auto. Connect your RCA cable to the camera cord'south video connector if necessary. Then, run it through your vehicle to the area by the fuse box. Depending on your vehicle model, you'll usually be able to do this by peeling dorsum the automobile's headliner or side panels and pulling your cable through the exposed chamber.^[10]
- For certain trucks, you may need to run the video cable through the vehicle's frame runway.
- In almost cars, you'll observe the fuse box underneath the steering wheel.
two
Ready external monitors to the forepart windshield. If you're installing an external monitor, first attach your device's included mount to the windshield past following the manufacturer's included instructions. Then, hook your monitor onto the mount.
- Near external monitors employ a suction mount, though others may come up with a more circuitous mounting system.
3
Attach internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll need to clip the new device onto your electric current rear-view mirror. For others, you'll need to take off the mirror and slide your monitor into the pre-existing mirror mount.^[xi]
- Some internal monitors may come with their own mounting system that yous'll have to attach to the auto's front end windshield.
4
Run the monitor'south splitter cablevision to the fuse box. If necessary, hook your monitor's power and video cable into the device. And so, route the cable from the monitor to the expanse side by side to the fuse box.^[12]
- If you'd like, use a trim removal tool to popular out the headlining console directly above your windshield. Then, run your cable through the exposed chamber.
5
Connect your monitor'south camera cable to the RCA cable. After routing your monitor'south splitter cable, connect the video terminate of the cable to your camera's RCA cord. Then, wrap the continued cords with electrical tape to concord them together.
- If your RCA and video cables accept the same ends, you may need to purchase an RCA male person to female converter string. You can observe these at about electronic stores.
half-dozen
Attach your monitor's power cablevision to a fuse tap. Connect your remaining blank wire cable to the fill-in monitor's power cord. Then, push the positive (usually red) stop of the bare wire cable into the open up finish of a fuse tap. Finally, crimp the ii cables together with a pair of pliers.^[13]
- A fuse tap is a modest cable that converts a bare wire into a fuse point. Y'all tin notice them at most machine part stores.
- If y'all'd prefer, you can leave the bare wire cable off and connect your photographic camera's power cable to a cigarette lighter adaptor. Then, plug this adaptor into your car's cigarette lighter receptacle for power.
7
Plug the fuse tap into the fuse box. Locate your fuse box and open it upwards. Then, plug your fuse tap into an open fuse cell. If necessary, check your fuse box'south lid or your vehicle'south educational activity manual to encounter which slots are open up.^[14]
- Later on attaching your fuse, consider taping all your wires together using electric tape to get them out of the style.
Advertising

ane
Connect your backup camera to its power and video cable. Return to the back of your car one time y'all've installed the rear-view monitor and all the necessary photographic camera cords. Close the torso if necessary, then connect the fill-in photographic camera to its power and video cable.
- Your camera'southward power and video cable should exist sticking out of the pigsty you drilled in the license plate mounting area.
2
Mount the photographic camera to your license plate. If the camera attaches to the front of your license plate, fix it to the plate by post-obit the manufacturer's included instructions. If the camera attaches to the back of your license plate, line the device up with the plate's fastener holes and thread screws through them.^[fifteen]
- In virtually cases, you can adhere a rear-view camera to the dorsum of your license plate using the screws you removed from the car before.
iii
Reattach your license plate and trim panels. Using a Phillips caput screwdriver, put your rear license plate back on your vehicle. Once yous've reattached it, give the license plate and backup photographic camera firm tugs to make sure they're secure.
- If you oasis't already, reattach your car'southward interior trunk panel and other trim panels by pressing them back onto the vehicle.
iv
Exam the photographic camera to make certain everything works. Before using your new camera on public roads, test it in a rubber surface area like your driveway. If it turns on, place a big, durable object similar a trash can behind the camera to see how distorted the epitome is. If information technology does non turn on, read your installation manual for troubleshooting information.
- In many cases, rear-view camera malfunctions are acquired by loose or improperly connected wires.
Advertisement

Add together New Question

Question

I hooked the camera upward and it only flickers. Whatever advice?

You may want to ensure all cables and connections are secured tightly. Double check that all connections are correct. If this doesn't piece of work, check to see if the photographic camera called is in skilful shape and isn't physically damaged.
Question

Suzuki installed contrary parking camera in my Swift Dzire Zxi. But the camera shows upper view and not the footing below. What can I do ?

Make sure that the camera is installed the correct mode (not upside down), and bank check the position of the camera mounted. Take it back to the dealer that installed it and ask them to check the alignment and fit.
Question

What is the best top for a reversing camera?

There is no optimal height for a dorsum-up camera. The ideal peak is based off the specific car or vehicle that you have and your personal preferences, along with its intended application. Some back-up cameras are placed on large service trucks and then that they tin can line up to trailer hitches easier, some are to foreclose a blindspot on the road. Depending on your awarding, it can exist placed at any height. Most reversing cameras are a "wide view" style and the specific superlative location does not always bear on the way it functions.
Question

So if I hooked up all the wires correctly simply still no power, is it a fuse tap that I need to splice into the wires for information technology to work correctly?

Shannon Phillips

Community Answer

Cheque your earth or ground information technology may be bad. Use your multimeter to see if the footing is okay.
Question

Is it still okay to connect the back-up photographic camera to the reverse light with cars that have automobile lighting? Or, would I need to connect to the reverse wire on the gearbox?

Shannon Phillips

Community Reply

Yep, that will exist fine, that how it is supposed to exist washed. Look for an machine electrician if you lot demand someone to call.

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Though most car dealers and mechanics will not install aftermarket backup camera systems, many sound and electronic shops will.

Advertizement

Make sure you lot turn the car off before working with bare or stripped wires. If you need to bear on exposed wires while the car is on, put on a pair of shock-resistant prophylactic gloves.

Things You lot'll Need

Rear-view camera
Rear-view monitor
Connector cables
Phillips head screwdriver
Trim removal tool
Power drill with high-speed twist flake
Safety grommet
Wire stripper or pliers
Electrical tape
Fuse tap

About This Article

Article Summary Ten

To successfully install a rear-view camera, outset remove your vehicle's rear license plate and interior trunk panel. Using a power drill, punch a pocket-size hole through the exposed license plate mounting area and run your camera'due south power and video cord through it. Attach a bare wire ability cable to your camera's ability connector, so strip your car'south reverse calorie-free wires and splice them with your bare wire power cable. To learn how to mountain the rear-view photographic camera and fill-in monitor, roll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 259,009 times.